+49 (0) 8076 - 9187-0 info@lisa-lift.de

Universal components

COMPONENTS FOR THE SAMI LANDING MODULES

LOPM – LOP module with matrix display

The LOP contains an LED matrix (16 x 24 dots) with the analogue functions of the small LBDS bus matrix display in vertical position of installation, i.e. it provides: landing and direction indication, operating states via scrolling text, assignment of landing symbols and texts via LiSA bus and parameters in the controller. Option: indication in blue, white or green LEDs.

LOPT – LOP module with TFT display

The LISY 2.8 is a landing panel known from the LOP series. The difference is that this circuit board  is equipped with a 2.8″ TFT display with a resolution of 320 x 240 pixels.

A gong and the acoustic acknowledgement are also found on the circuit board. Various display and background images can be loaded via an SD card. The display is controlled via the LiSA-BUS or alternatively via CANopen.

 

LOPP – LOP module with arrows

The LOP contains 30 mm LED arrows and an out-of-order indicator field.

 

LOPO – LOP module without displays

This is the eco-variant. The LOP only contains the bus electronics. The (functionless) housing for the arrow display is installed as a dummy.

 

LISY

LISY is a program, which can be installed on all computers with windows operating system.

Connection LISY to LiSA20

► Serial (RS232) connection
 by means of a serial Bluetooth adapter (S2BT) with Bluetooth interface of the LISY
 developed by Schneider.

► Connection by means of LiSA bus
 with another adapter developed by Schneider (LB2USB).

Due to available software modules (LiTerm and LiSY) for Windows, it is possible to use LISY in two fully independent areas:

► as a control module (LiTerm), i.e. a hand held terminal without stationary installation
► as a multifunctional module with a collection of features that can otherwise only be achieved through a number of modules.

LISY with LiTerm application as a control module (hand held terminal):

An additional advantage and an absolute novelty, is the use of the LISY as a control module for LiSA20-controls. So far, the preferred operating module has consisted of a LISY4 display with an RS422 connection for LiSA20.

LISY makes it possible to set the LiSA20 controls and thus DCP-enabled inverters without a physically existing connection in the distance of up to 50 meters (depending on capabilities of a Bluetooth module), to read out recorded error and status memory messages, to observe current processes on the system, to give commands, and to set any IO.

LISY as multifunctional module:

LISY can be used als multifunctional system.

In addition to the usual function to inform the lift user (info module), it may well fulfil the function of a complete cabin or landing panel (command modul) and of an access control system (control module).

Examples as info module:
(Stand and direction indicator, floor-info fields, lift data, operating state, voice output, gong, emergency pictograms etc.)

Examples as a command module:
For inputting the call signal on the cabin or floor display (call button field on the tablet screen).

LISY5

LISY5

A full-colour landing or car display (5.7″) with touch screen and a 640×480 pixel resolution (VGA). Integrated voice announcement and gong.

Technical data:

● Resolution, colours: 640 (V) x 480 (H), 16,7 mio.

● Active area: 116 x 87 mm

● Typical viewing angle: viewing from 6 o’clock 85°/30° from top

● Touch panel: 4-wire resistive

● Brightness with touch: 350 cd/m²

● Brightness without touch: 400 cd/m²

● contrast: 350 : 1

● Backlight: LED

● Signals: LiSA bus/ conventional

Special versions on request.

Examples: